Monday, 11 June 2012

HSG Mod front end design thoughts.


The HSG mod has a slightly different approach to the real valve gain setting and positioning of the voicing RC network attenuator compared to the original Soldano design.  Though not the final design this is a dialogue covering the thoughts I had in approaching the modification.  I will concentrate here primarily on the input stage and what I attempted to do to make more sense of the setting.  All values are from SPICE simulation using Microcap 9 evaluation edition from Spectrum software.  This is a free download and contains the 12AX7 / ECC83 models as standard from Duncan Munroe. 

The standard stage is set up pretty much from the off as a high gain amplifier. The valve is operated at a high gain and then droped with a passive resistor network with 1Meg as the gain pot This generates a lot of resistor noise and susceptibility to interference being a high impedance point then amplified by the rest of the preamp. The gain of the input valve is a combination of the anode resistor (220K) and the load resistor (1Meg pot + series resistor) over the cathode resistance.

 For the Soldano design below, with a 100mV input at the point marked VG1 the voltage at the V1A anode is 6.26V pk-pk or a gain of 62.37. However at point A at the input of the second stage and after the 1Meg series resistor the overall gain achieved is now 27.6 with the gain pot set to 100%. The quandary is that whilst 62.7 is pushing the valve fairly hard the overall gain achieved is modest, and I still have an issue with all that impedance and resistor noise on the input of the second stage.


In changing the GAIN pot to 100k in lieu of 1Meg it will reduce the resistor noise into the second stage but lower the gain of V1A. I can re-jig the gain by shorting out the attenuator R53. With a 100k anode resistor the valve gain is now 35.6 and due to effectively removing  R53 it remains at 35.6 at point A.  There is no blocking at the point between V1A and V1B.

All this doesn’t come without cost, the AC frequency response curves for both circuits are quite different.  However the low frequency  is recoverable by increasing C27 from 1uF to 4.7uF. The final curves are shown below. The red is the standard circuit with 100% gain at point A, the blue is modified including C27 = 4.7uF. 
The Soldano circuit also has a low frequency response that flattens and extends way below bottom E and into hand-on-string and bump noise and I didn’t see that helping either.  The modified circuit has a much wider frequency plot, so I can easily tweak the circuit to lose or re-voice this. The original circuit is pushed so especially at the high frequency end it is what it is.
 I worry that I have missed something here as I seem to find 1 meg-ohm as the default go-to value for the gain pot, and to me that doesn’t make sense.  

I should note that the dynamic range of the modified circuit is reduced because of the bias being unmoved but it will still take a 2.5V pk-pk signal before clipping the first stage which should be enough. If your humbucker is hotter than this then you are probably after clipping anyway. The important thing is that the modification can be tried without removing parts from the PCB and just placing parts or wires in parallel with the existing circuit. By reducing the gain of the valve I also hoped to remove some of the valve to valve dependency that other uses have reported. In the original design the high frequency end is dominated by the valve and not by circuit values.

Friday, 18 May 2012

Jet City DIY front panel.

The Jet City JCA20 comes with a "Marmite" front, you either love it or hate it. I am in the latter camp so decided to do something about it. At the same time I changed the knobs and the guaranteed-to-fail blue lamp. The panel was MDF and the cloth was from a previous project giving an old Peavey combo a face lift.

The whole surface had contact adhesive rolled on and when firmly stuck down staples were banged in at the rear to stop edges lifting. I wiped the back panel over with some blue fountain pen ink as a colour wash as you can see this from the back.  I did try some black chicken head knobs that I already but you just couldn't see where they were pointing.

The bottom edge of the new front had some router-love in the way of a round-over bit on both the front and the rear of the panel. The one on the back of the panel, though not visible makes a good gap for air-flow.




Monday, 14 May 2012

Grain Fill with Acrylic paint and Superglue (CY Glue)

The guitar build nearing the point where I need to think about the finish of the guitar, and having used Sepele, Black Walnut and Oak I felt it would be a shame not to use a transparent lacquer. However a test spray quickly showed how open grained all three are. The largest grain or pore voids by far are in the oak. I looked at all sorts of grain filler and followed a lot of posts suggesting cyanoacrylate (CY, crazy glue or superglue) which looked promising.

However in attempt to speed this up I decided to use a gold metallic acrylic paint to fill the large gaps and then CY glue to then grin fill the rest. I added about 30% volume of water to the acrylic paint and then rubbed it into the surface removing as much excess from the surface as possible. I then rubbed it down with 400 grit  and then sealed with superglue and left it to set. After initial sanding the finish is better than I expected. The gold has filled the largest voids and is _just_ visible when at the right angle. The end grain took more paint but here is an image of the top. I am very happy with this grain fill, the gold goes really well with the oak.

 I will add that I masked the black walnut and Sapele off so they just had the superglue grain fill. The superglue took three wipes and sanding to fill all the grain, but it's easy to work so it's just time spent more than anything else.

Below, poor picture but you can just make out threads of metalic gold acrylic grain fill in the oak. It looks slightly proud of the surface, but isn't.


Tuesday, 1 May 2012

Routing Out A Guitar Body.

I have started a new project based around a neck I got from Ebay. It was a 24 fret neck from an Aria M series in red. I have designed and routed out a body and have found the following useful.
1. Polish the base of the Router!
I used domestic spray furniture polish, and then buffed it dry with a cloth. I can't tell you how much of a difference this makes in controlling small movements of the router. I have since found that professionals use a spray on PTFE dry lubricant and I can see why. Not seen this tip anywhere else so maybe I am the only person who wasn't lubricating the base and everyone else already knows.
2. Never try for the BIG cut. 
I _gradually_ worked my way to the line. I had made a template and used a combination of cutters with the bearing at the top and bottom to get the body shape cut. The template had two layers of tape added to the edge at this stage which for the final pass (full length 50mm cutter with end bearing to do the 41mm body) I removed. The removal of the tape meant that the final pass was quick, without grab and left virtually no burn marks.
3. Keep EVERY off cut.
Practise for the large diameter bridge and tailpiece holes, finishing techniques, trial cutting, trial trim tools, you name it, keep all the offcuts you have.

I'll quickly run through the process that worked for me.

I managed to find some offcuts in a local timber supplier. A block of Sapele, a length of Black Walnut strip and a good chunk of Oak which had bounced on the planer and therefore had a defect area. All good low cost stuff. I cut and glued the wood to make a body-blank-sandwich. I made a Router-Planer from ideas on the Internet and trimmed it to 41mm

The first part was to draw a body shape. I used Paintshop to scale a PRS guitar body photo to real size using 150 pixels to an inch. I then used the distort tools to move the basic shape around and then used the curve draw tool to make new edges and lines. I could then print a portion of the overall design to A4 paper as full scale. By splitting the design into three sheets I could then print real-scale drawings taping together the sheets.  I included some red thin construction lines to aid alignment of the drawings. By the 8th design, iteration F it bore no resemblance to the PRS original and  I had a finished print which I glued down to 12mm thick MDF board. The MDF cuts well with a thin smooth cut Jig Saw blade and then I used a rasp (bottom of picture) and sandpaper to smooth the edges. Smooth lines here will pay dividends later and MDF is a lot softer than Oak.



The addition of drawn pickups and the neck cavity proved useful as well as the centre line being pre-printed. The final bridge will be a Les Paul type and not a Strat hardtail as in the original drawing.

The design was then transferred to the body blank and drawn on both sides. The blank had a centre line drawn on both sides. The distance from the base of the guitar from the edge ensured I was within a mm or so on both sides.



I then hand routed close to the edge with a 6mm dual cut router blade. This was SLOW work. You have to  go in 5-6mm depth steps but eventually you will remove wood and also end up at the depth limit of the cutter.


This is where accurately marking out on both sides with the template comes in. I then flipped the body over and began cutting again, though a bit further away from the line this time. As you can see below, I got daylight at last.


The template was then refitted and SCREWED to the top. This is where having the pickup marked acts as a sanity check when sticking a screw in. I started with a template cutter (bearing at the top) to cut an inch below the template. I then turned the body over and used a trim cutter (bearing at tip) to follow this cut and remove the rest of the material in a gentle manner.  As you can see below all the initial iterative cutting has left burn marks. For the final cut I removed the white tape and went with a full length cut trim cutter.



I have seen people using double sided tape to secure the template but I was glad I opted to use screws. I ended up moving the neck screw as I couldn't find a countersunk head screw and it got in the way of the router.


After the final cut very nearly all the burn marks were removed and the body had a good clean line and more importantly cleanly cut with no tear-out. Overall very pleased with progress so far.I'll update with more pictures as this progresses.




Sunday, 15 April 2012

Ebay Refret with EVO Gold and filler


I got a Profile Silhouette Strat copy off ebay. I paid £115 for a made in Japan Stat, about 30 years old in good condition advertised with not much fret wear. However on receipt it was evident that it had spent a good deal of time playing rhythm on the first five frets as several areas were utterly shot. I decided to keep the guitar but attempt my first refret. After some research I stumbled across EVO gold fretwire. It's _marginally_ more expensive than standard nickel silver, but much more wear resistant and has a nice gold hue to the metal. 


On removing the frets I noticed exactly how deep the slots are compared to the fret tang and how much more the neck moved in my hands. The frets are obviously part of the structure and rigidity of the neck. That and  and I am now working old fret slots. It can't be good.  My solution was to use a resin wood filler to pack the slot prior the instant before fitting the fret. I placed electrical tape either side of the fret slot, filled the slot quickly and then pulled the tape. This leaves a clean surface and a well filled slot. The wood filler cures very quickly so it was one slot at a time. The excess appears out of the side of the slot so it doubles up as the slot filling job at the same time. The truss rod plays a lesser part now as the fretboard in more structural than before.  Six months later there are no issues. I am sure someone will have an problem with filling the slot but in this instance it seems to have worked a treat.


 As for the Jescar EVO gold fretwire, it works easily, polishes beautifully and string bending is all too easy. Someone please explain why EVO Gold isn't used on everything now and why I have to spend a fortune with Gibson before they will fit it. It costs about £2 more than nickel.... As for the Profile copy, with some decent pickups now installed you would never put it down for a Fender seven times the cost. Below, banging in the frets and taping up for the next swipe of plastic wood filler. I hope it shows the gold in the fret, and when polished it's like glass.


Added photo below as this is in natural sunlight which correctly shows the subtle gold. The dot markers were also changed on the guitar. The standard dots fitted were white plastic so I bought a pack of MOP (mother of pearl) the same size. Removal of the old dot markers was simple. You just stick a soldering iron into the middle and gently rotate it round. The plastic melts first and the glue soon follows allowing for a very clean removal of the old dot marker.


Wednesday, 22 February 2012

Tag board vs PCB construction.

Whilst I have a deep loathing for voodoo electronics one conclusion I have arrived at is that tag-board construction will produce a different tone from the same design based on a PCB, and I believe that tag-board can prove best. So how did I arrive at this conclusion? 
I built a tag-board (not a turret board) based amp a while back with a fault. It was missing a wire that connected the preamp signal to the power output stage. So the amp was dead, right? Well no, it carried a very trebley signal at a low level to the speaker just because the components on the tag-board are forced to be so close together. This isn’t voodoo its called crosstalk and is well understood. I found the fault and the amp sprang to life. So it has a feed-forward path and a bit of treble gets added from somewhere to somewhere else, well so what.   
Well try an experiment, find a HiFi loudspeaker that has a Bi-wire option and play something familiar. Now disconnect the tweeter and have a listen, half the sound disappears and what is left is muddy and pretty torrid.  Lastly disconnect the woofer and connect just the tweeter.  It’s all treble as expected but the volume level compared with the woofer is fractional. Conclusion:- A small amount of treble carries the weight of the sound. Now back to the tag board where co-located components will cross-talk and bleed treble forward in the amp. I loaned the amp to a friend to check it out at volume, he concluded that it had an “air” …. and I think I know where it comes from.

Monday, 30 January 2012

JCA20H with EL84 Triode / Pentode Switch and schematic circuit diagram.

Though the JCA20H is _only_ 20watts, you have to take account of how loud 20 watts is, how you define 20 watts (some define it at 1% THD, some at 5% THD, it makes a big difference) and how efficient your speaker is. I decided as it's a simple mod to put in a triode switch which simply drops the output power to about 10 watts. However I found that the triode mod has develops a much smoother tone which I like. A fly in the ointment is that I also unbalanced the phase splitter at the same time, so two variables at the same time. 
However looking at the spectrum for Pentode and Triode shows that the harmonic balance shifts and that the change in tone is not just perception and that switching a EL84 output stage between Pentode and Triode is not only an output power change. (unless the phase splitter modification has also contributed)

The initial test setup was to keep the input stage as clean as possible and then drive the output stage in pentode configuration to 5% THD into a 8ohm resistive load.

The normal Pentode spectrum (500Hz sine input) looked like this.

Pentode 5%THD into 8 ohm.

When switched to Triode mode the THD  increased by 1.2% and the upper spectrum changed structure.

Triode mode.

With the input gain set at maximum and clipping in the pre-amp you can see how the different operating modes modify the tone. In Pentode mode the dominant harmonic structure from the overdrive is clear.


In Triode mode again the upper harmonic structure produced from the preamp is modified.




 In the final version I fitted R7 and R5 (470R) as 1k5, 5 watt.  C-8 Helps keep the supply stiff, R-6 brings the phase splitter value from 82k to 50k which skews the output balance and allows the output stage to generate second harmonics (ongoing trial) C-6 reduces the power stage bandwidth to about 10kHz. The depth mod is from the web to boost low frequency.


JCA20H HSG output stage.
I did play with the idea of having SW1 as two separate switches so I could run one valve in pentode and one in triode in lieu of messing with the R46 value in the phase splitter but I didn't get around to it. You do loose some output power in changing the R46 value, but it is negligable.